Texas Instruments Network Router CC2530ZNP User Manual

SWRU268A  
October 2010  
CC2530ZNP Mini Kit Quick Start Guide  
STEP 1 – Introduction  
Target Boards  
This guide describes how to set up a CC2530 ZigBee® Network Processor (ZNP)  
development kit using the preprogrammed devices of the CC2530ZNP Mini Kit.  
The ZigBee Network Processor development kit is designed to give a simple  
introduction to ZigBee wireless networks. The hardware consists of a CC2530  
ZigBee device preprogrammed with ZigBee software and an MSP430F2274  
microcontroller that controls the ZigBee device.  
The development kit demonstrates examples of typical sensor networks with  
temperature, light, voltage, and movement sensors.  
The target board connected to the USB stick is programmed with a coordinator  
sample application. The coordinator sets up the network and configures the ZigBee  
network parameters. A ZigBee system can only have one coordinator.  
Battery Sensor  
(End-Device)  
USB Stick  
(Coordinator) (End-Device)  
Battery Sensor  
The battery powered sensors are end-devices that periodically report their key  
data to the coordinator. The devices can also be programmed as routers. Routers are typically used to extend the  
ZigBee network since they can route messages from other devices. Note that hardware for all the target boards is  
identical. Each of the boards can be programmed to be coordinator, router, or end-device.  
STEP 2 – Install the sample software and connect the USB stick  
Download the CC2530ZNP example software from  
Target Board  
USB Stick  
Double-click the installer file to install the example software package and drivers.  
After installation the default location for the sample software is  
C:\Texas Instruments\CC2530ZNP Mini Kit  
Connect the USB stick to a USB port on the PC. The Windows new device driver will  
request a new device driver to be installed. Normally the driver should be detected  
automatically. If the driver is not detected it can be found at the default location:  
C:\Texas Instruments\CC2530ZNP Mini Kit\Drivers  
After installation a new COM port will be installed on the PC. To see  
the COM port number, open the Windows Control panel – System  
– Hardware – Device Manager and check the COM port number  
under Ports (COM and LPT).  
The USB stick serves both as a virtual serial port interface and as debugger/programmer. This means that during normal  
operation the USB stick should be connected to the coordinator target board. The USB stick can also be used to  
program and debug the end-device target boards using the IAR Embedded Workbench.  
STEP 3 – Start the network  
The ZigBee coordinator on the USB stick connects to the PC using a virtual USB serial port.  
The serial port interface can be accessed through a terminal program. The Windows default  
terminal interface can be found on the Windows Start menu - Accessories-  
Communication – Hyperterminal.  
After starting HyperTerminal, give a name to the connection and select the COM port used by  
the USB stick. In the COM port properties, select 9600 baud, 8 data bits, no parity, 1 stop bit,  
no flow control  
Push the button on the target board to display the status  
window of the network after the terminal has connected.  
Information about the ZNP and device is displayed. The  
coordinator is now ready to connect to other devices on  
the network. For more information about the message  
format, please see the Simple Application wiki page:  
1/2  
 
IMPORTANT NOTICE  
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,  
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should  
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are  
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.  
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard  
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where  
mandated by government requirements, testing of all parameters of each product is not necessarily performed.  
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and  
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide  
adequate design and operating safeguards.  
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,  
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information  
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a  
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual  
property of the third party, or a license from TI under the patents or other intellectual property of TI.  
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied  
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive  
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional  
restrictions.  
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all  
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not  
responsible or liable for any such statements.  
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably  
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing  
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and  
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products  
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be  
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in  
such safety-critical applications.  
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are  
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military  
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at  
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.  
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are  
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated  
products in automotive applications, TI will not be responsible for any failure to meet such requirements.  
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:  
Products  
Applications  
Audio  
Amplifiers  
Data Converters  
DLP® Products  
Automotive  
Communications and  
Telecom  
DSP  
Computers and  
Peripherals  
Clocks and Timers  
Interface  
Consumer Electronics  
Energy  
Logic  
Industrial  
Power Mgmt  
Microcontrollers  
RFID  
Medical  
Security  
Space, Avionics &  
Defense  
RF/IF and ZigBee® Solutions www.ti.com/lprf  
Video and Imaging  
Wireless  
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265  
Copyright © 2010, Texas Instruments Incorporated  
 

TDK Network Card HHM1775B1 User Manual
Teac DVD Player PortaDVD User Manual
Thermador Outdoor Kitchen Island CGB30RCULP User Manual
The Singing Machine Karaoke Machine Singing Machine User Manual
Trane Thermostat VAV SVX02B EN User Manual
Tripp Lite Network Cables P753 010 User Manual
Tripp Lite Telephone H2513 User Manual
VocoPro Karaoke Machine DVX 668K User Manual
Wasp Bar Code Scanner WDT2200 User Manual
Weber Gas Grill 2000 LX User Manual