Toshiba Camcorder IK VR01A User Manual

INSTRUCTION MANUAL  
CCD COLOR CAMERA  
IK-VR01A  
Please read this manual thoroughly before use, and keep it handy  
for future reference.  
Record in space provided below the Model No. and  
the Serial No. as found on the label on the bottom  
of this unit.  
Model. No. IK-VR01A Serial No.  
Retain this information for future reference.  
TABLE OF CONTENTS  
Important safeguards  
1. Features & Description ................................................. 3  
2. Cautions........................................................................ 3  
3. Components ................................................................. 3  
4. Part Names & Functions ............................................... 4  
5. Connections and Operations ........................................ 5  
6. Installations ................................................................... 7  
7. Line Lock Phase ........................................................... 12  
8. Note on use and Installation ......................................... 12  
9. In Case of Problems ..................................................... 13  
10. Specifications................................................................ 14  
11. Exterior View................................................................. 15  
 
The CAUTION label, shown on the left,  
is attached on the camera.  
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE COVER (OR BACK).  
NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lightening flash with arrowhead  
symbol, within an equilateral triangle,  
is intended to alert the user to the  
presence of uninsulated dangerous  
voltagewithin the products enclosure  
that may be of sufficient magnitude to  
constitute a risk of electric shock to  
persons.  
WARNING :  
TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR  
MOISTURE.  
CAUTION :  
CONNECT 24V AC UL LISTED CLASS 2  
POWER SUPPLY.  
The exclamation point within an  
equilateral triangle is intended to alert  
the user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
accompanying the appliance.  
FIELD INSTALLATION :  
WORDED : THIS INSTALLATION SHOULD  
BE MADE BY A QUALIFIED SERVICE  
PERSON AND SHOULD CONFORM TO  
ALL LOCAL CODES.”  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instruction manual, may cause harmful interference to radio  
communications. Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at his own expense.  
USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment could be  
voided if you make changes or modifications not expressly approved by the party.  
Serial No Label  
The serial No. label is located here.  
- 2 -  
 
1. FEATURES & DESCRIPTION  
IK-VR01A has the following features:  
(1) Flush/Surface mount.  
(2) IP66 Standard for dust and water resistance.  
(3) Built in vari-focal lens with auto-iris  
Focal length 3.0~8.0mm.  
(4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent  
sensitivity  
480 lines horizontal resolution  
0.4 lx minimum illumination with tint dome cover  
(5) 50dB Signal-To Noise Ratio  
(6) Power supply- AC24V or DC12V - This camera automatically detects the power.  
(7) BLC, AGC, and Line-Lock (AC24V)  
2. CAUTIONS  
(1) Avoid touching the lens glass with your fingers. If necessary, use a soft cloth  
moistened with alcohol to wipe off any dust.  
(2) Avoid aiming the camera at the sun.  
(3) Avoid shooting the camera at intense light. Intense light such as a spotlight may  
cause a bloom or smear. A vertical stripe may appear on the screen.  
However, this is not a malfunction.  
(4) Install the camera away from video noise. If cables are wired near electric lighting  
wires or a TV set, noise may appear in images. In this event, relocate cables or  
reinstall equipment.  
3. COMPONENTS  
(1) Camera (with Tint Dome Cover installed)  
(2) Accessories  
1 pc.  
(a) Mounting Base  
(b) Bracket  
(c) Screw A  
(d) Screw B  
(e) Clear Dome Cover  
(f) Special Hexangular Wrench  
(g) Monitor Out Harness Wire  
(h) Power Connector  
(i) Instruction Manual  
1 pc.  
1 pc.  
3 pcs.  
3 pcs.  
1 pc.  
1 pc.  
1 pc.  
1 pc.  
1 pc.  
- 3 -  
 
4. PART NAMES & FUNCTIONS  
Lens Iris ADJ  
Counterclockwise: The picture becomes  
Mode Setting Switch  
darker.  
BLC (Backlight Compensation Switch)  
With the switch on, it adjusts  
the backlight automatically to  
obtain the best possible image.  
LL  
Sets camera synchronization  
to line lock with the switch on.  
Available only with AC24V.  
LL BLC  
Clockwise: The picture becomes  
brighter.  
"Optimum Value" is at default setting.  
ON  
OFF  
Line Lock Phase ADJ  
Adjusts the phase of the line lock.  
Monitor Out Connector  
Connect with the supplied monitor out  
harness wire. Used to adjust the angle of  
view when installing the camera.  
- 4 -  
 
5. CONNECTIONS AND OPERATIONS  
Notes on connecting  
Power plugs to connected equipment must be disconnected before installation.  
A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection.  
For details of wiring and operation of equipment to be connected, refer to their  
operation manuals.  
Coaxial cables for video signals and the power cord are not supplied with the  
camera.  
Refer to the operations manuals of connected equipment for detailed wiring and  
overall operation instructions.  
5-1 Basic connection single system configuration  
Video Monitor  
BNC Connector  
Supplied Power Connector  
12V DC  
( ) POWER CORD (twisted pair line)  
AC 120V  
minimum wire size of 18 AWG is recommended.  
24V AC UL Listed Class 2 power supply / 12V DC power supply  
CAUTION : Never input 24V AC and 12V DC at the same time.  
In case of DC12V, connect +12to red cable and GNDto black cable.  
Do not overload power supply  
Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power  
supply, it should be connected to a power supply that allows for at least 5w  
consumption. Because the IK-VR01A uses a mechanism, a sufficient power supply  
with adequate current specifications is required.  
- 5 -  
 
5-2 Line-Lock Control  
Matching the vertical synchronization with the power frequency is called the Line-  
Lock.  
This function is activated when the LL of Mode Setting Switch is on.  
When two or more cameras are switched by the video switcher for viewing by a monitor  
TV, the vertical sync. phase can be locked with the power frequency, and a stable  
vertical sync. is obtained without being disturbed at the time of switching.  
Video Monitor  
VIDEO SWITCHER  
CAMERA1  
TO AC 24V UL Listed  
class 2 power supply  
When connecting to DC  
power supply, the Line-Lock  
function is not activated.  
CAMERA2  
Note :  
The camera is synchronized to the power frequency of 60±1Hz covering a normal  
fluctuation of the power frequency. However, the camera may not cover a large  
fluctuation caused from the power generated by an engine generator, etc.  
It takes about 10 seconds or more until a stable synchronization is obtained after  
the power is turned on. This is normal, because several seconds are required to  
stabilize the camera against power noise.  
Refer to 7. LINE-LOCK PHASEfor adjustment.  
- 6 -  
 
6. INSTALLATIONS  
Connect the cable of the camera and the cable from the designated power supply  
with respective connectors.  
Screws for fixing the camera and mounting base to the ceiling or wall are not supplied  
with the unit. Use appropriate screws.  
Note :  
The weight (camera body only) is about 1.3kg. The camera unit including the mounting  
base and the bracket weighs 2.1kg.  
When installing to surfaces of other materials, use the screws to fix it firmly.  
6-1 Adjust the Angle of View  
Security screws  
Top Cover  
a
Camera Base  
(1) Loosen the three security screws by the supplied special hexangular wrench and  
remove the top cover.  
Important Notice :  
a
Be sure to remove three silver screws  
immediately after removing the top  
cover. The screws are used to temporarily fix the top cover for transportation.  
- 7 -  
 
Tilt rotation  
Horizontal  
rotation  
a
2
a
Tilt Lock  
FAR  
1
Pan Lock  
4 Focus  
lock lever  
NEAR  
WIDE  
TELE  
a
3
Zoom  
lock lever  
Remove three silver  
screws transport protection.  
Pan  
a
Transport Protection Screws (silver)  
(2) The lens direction in pan direction can be adjusted by turning pan lock  
1
counterclockwise to unfasten it without moving the lens. After adjustment, turn pan  
lock  
clockwise to fasten it.  
1
Note :  
Do not turn the lens over 360°. Otherwise the inner connector may be broken and  
the image may not appear.  
(3) The lens tilt angle can be adjusted by loosening the tilt lock . After adjusting,  
2
tighten the tilt lock  
.
2
(4) Adjust the zoom position by loosening the zoom lock lever  
. After adjusting,  
3
tighten the zoom lock lever  
.
3
(5) Adjust the focus by loosening the focus lock lever . After adjusting, tighten the  
4
focus lock lever  
.
4
(6) Repeat the adjustments from step (1) to step (5) till the optimum image appears.  
- 8 -  
 
6-2 Installing the Camera Unit  
6-2-1 Installation to Wall or Ceiling with Mounting Base (Surface Mount Installation)  
Cable access hole ø27 mm  
When installing the camera unit on the  
wall, mount it with the drain groove on  
the downside. Do not block the drain  
groove.  
46 mm  
C
Mounting Base center  
46 mm  
B
When installing the camera unit outdoor,  
make waterproof for the cables. The  
camera body is water-resistant but the  
brackets are not water-resistant.  
83.5 mm  
85 mm  
A
Mounting Base center  
55 mm  
83.5 mm  
Mounting Base  
Drain groove  
A , C Wall or Ceiling  
B , D Junction Box  
85 mm  
55 mm  
Cable access hole  
ø27 mm  
With female screw for piping  
Cable exit  
(sideway)  
D
Rear cable hole  
Drain groove  
In case of using the  
variable mounting  
holes  
Screws (not supplied)  
x4  
Fix firmly.  
Align to this mark.  
Screws  
x3  
Mount the top cover (the  
assembly of the dome  
cover) and secure it firmly  
with three security screws  
by the supplied special  
hexangular wrench.  
Mount camera base with three supplied  
screws A. (Longer screw(M4x16))  
Tighten and lock the screws firmly.  
Top Cover  
Camera Base  
Align to this mark.  
- 9 -  
 
6-2-2 Installation to Junction Box with Bracket (Flush Mount Installation)  
46 mm  
Junction Box  
83.5 mm  
Bracket  
Screws (not supplied)  
x4  
Note the direction of  
the bracket, which has  
two sides.  
Align the marks.  
Screws  
x3  
Mount camera base with three supplied  
screws B. (Shorter screw(M4x10))  
Tighten and lock the screws firmly.  
Mount the top cover (the assembly  
of the top dome cover) and secure  
it firmly with three security screws  
by the supplied special hexangular  
wrench.  
Align to this mark.  
- 10 -  
 
6-2-3 Change of Dome Cover  
Screws (x3)  
Retainer plate  
Put the protruding side downward.  
The protruding portion should be set  
in the groove of the shock damper.  
Shock damper cushion  
Note the direction of the damper  
cushion.  
The groove should be face up.  
Dome cover  
Gasket  
Top cover  
Dome replacement  
When the dome cover is damaged or to be replaced by  
a transparent cover, call your distributor or sales person.  
Firmly tighten three mounting screws.  
Take care not to let dirt or foreign object enter between  
the parts.  
- 11 -  
 
7. LINE LOCK PHASE  
When a video switcher switches two or more cameras, the picture may fluctuate on the  
video monitor due to the different AC line phase of each camera. In this case, adjust the  
V PHASE controller to get a stable image.  
Line Lock V PHASE CONTROL  
8. NOTE ON USE AND INSTALLATION  
• Do not aim the camera at the sun  
Do not aim the camera at the sun or point it at sun even if you are not shooting.  
• Do not shoot intense light  
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may  
appear on the screen. However, this is not a malfunction.  
• Treat the camera with care  
Do not drop the camera or subject it to strong shock of vibration. Otherwise, the camera  
may malfunction.  
• Never touch internal parts  
Do not touch the internal parts of the camera other than the parts specified. Otherwise,  
the camera may malfunction.  
• Do not splash water on the camera  
Install the camera where the camera can be kept dry. If the camera gets wet, turn off  
the power and contact your dealer.  
• Check the ambient temperature and humidity  
Avoid using the camera where the temperature is hotter or colder than specified.  
Otherwise, the quality of images may deteriorate or internal parts may be affected.  
Special care is required to use the camera at high temperature and humidity.  
• Should you notice any trouble  
If any trouble occurs while you are using the camera, turn off the power and contact  
your dealer. If you continue to use the camera when there is something wrong with it,  
the trouble may much worse and an unpredictable accident may occur.  
- 12 -  
 
9. IN CASE OF PROBLEMS  
Condition  
Check Points  
No image  
Are the camera and connected equipment turned on?  
Are cables connected correctly?  
Unnatural color  
Is the monitor TV adjusted correctly?  
Is the lighting too weak?  
The image is out of Is the lens focus adjusted?  
focus.  
Is the lens or cover dirty?  
Are there any large barrier or bright illumination near the  
camera?  
The image is dark.  
Is the lens iris adjustment volume correctly set?  
- 13 -  
 
10.SPECIFICATIONS  
1. Image System  
Image Device  
Pixel Elements  
1/3IT CCD  
771 (H) x 492 (V)  
2. Electrical  
TV System  
2:1 Interlace, 15.734KHz Horizontal, 59.94Hz  
Vertical  
Horizontal Resolution  
S/N Ratio  
480 TV lines  
50dB (TYP. White 100%, Weight On, SC TRAP ON)  
Minimum Illumination  
0.2 lux (More than 10% of image output, Clear dome cover)  
0.4 lux (More than 10% of image output, Tint dome cover)  
Auto Gain Control (AGC)  
Iris Control Mode  
White Balance  
Average AGC (24dB)  
Auto Iris Lens  
Auto  
White Balance Range  
2500°K ~ 10000°K  
Line lock Vertical phase adjustment Provided (VR : range 300deg)  
Gamma compensation  
0.45  
Backlight Compensation (BLC) On / Off (DIP-SW)  
Video Output Signal  
VBS (1.0Vp-p, 75ohm unbalance, BNC)  
Synchronization System  
Internal for DC or Linelock for AC  
3. Mechanical  
Weight  
Camera : 1.3kg, Mounting Base : 0.6kg,  
Bracket : 0.2kg  
Dimension  
Camera : 170mm (D) x 150mm (H)  
with Mounting Base : 175mm (D) x 155mm (H)  
4. Optical  
Built-in Lens  
Vari-focus Lens  
f=3.0 ~ 8.0mm, F1.0 (Wide) /F1.45 (Tele) : Auto Iris  
View Angle  
Wide : 117.3° (D), 90.8° (H), 66.6° (V)  
Tele : 45.2° (D), 36.2° (H), 27.0° (V)  
Focus Length  
0.2m ~ ∞  
5. Power  
Input Voltage  
Power Consumption  
6. Environmental  
Operating Temperature  
Storage Temperature  
Water proof:IP66  
7. Regulation  
DC12V or AC24V  
3.0W  
-10°C~50°C 90%RH max  
-20°C~60°C 70%RH max  
Safety  
UL2044  
Dust and Water Resistance IP66  
Emission  
FCC Class A / DOC ClassA  
Design and specifications are subject to change without notice.  
- 14 -  
 
11. EXTERIOR VIEW  
unit : mm  
(
48.5  
)
(
110  
)
(
155  
)
- 15 -  
 
unit : mm  
(
150  
)
(
41  
)
(
61.5  
)
(
147.5  
)
- 16 -  
 
Bracket  
unit : mm  
4-M4  
120  
46  
110  
4-  
φ
4.5  
4-  
φ
6.5  
Mounting Base  
85  
46  
4.4  
20  
82  
6-  
φ
5.5  
4-M6 Depth=10  
4-  
φ
6.5  
φ 27  
15  
40  
15  
55  
- 17 -  
 
- 18 -  
 

Targus Mouse Wireless Multimedia Presenter with Trackball User Manual
Technics Car Speaker SB A386 User Manual
Telect Network Router 007 0001 2600 User Manual
TiVo Staple Gun Series2 User Manual
Topcom Cordless Telephone OGATECH OG S60 User Manual
Toshiba Projector TDP T91 User Manual
Triarch Indoor Furnishings 30024 User Manual
Tripp Lite Surge Protector SK6 0 User Manual
TV Ears Clothes Dryer DRI DOCK User Manual
Watlow Electric Network Card Series 97 User Manual