Transition Networks Power Supply CPSMP 120 User Manual

User’s Guide  
CPSMP-120  
AC Power Supply Module  
• PointSystem™  
• CPSMC13xx-100 Accessory  
0
I
The Transition Networks CPSMP-120  
power supply is an AC slide-in-module  
that provides optional, redundant  
power to the CPSMC13xx-100  
PointSystem™ 13-slot chassis and any  
installed media converter slide-in-  
modules and management modules.  
The figure below illustrates the components of the CPSMP-120 power supply:  
An On/Off switch that, when set to “I”, allows the power supply module  
to supply power to the chassis, and any installed modules.  
A panel fastener screw that secures the power supply module to the  
chassis.  
A power LED indicator.  
A handle for installing and removing the power supply module to/from  
the chassis.  
A fuse installed in a fuse holder.  
An external power connector that supplies power from a standard AC  
wall outlet.  
On/Off Switch  
Panel Fastener Screw  
Power LED  
Handle  
Fuse Holder  
External Power Connector  
Install the CPSMP-120 . . . . . . . . .3  
Connect to External Power . . . . . .4  
Replace the CPSMP-120 . . . . . . . .5  
Replace the Fuse . . . . . . . . . . . . .7  
Technical Specifications . . . . . . . .8  
Troubleshooting . . . . . . . . . . . . . .9  
Compliance Information . . . . . . .11  
 
CPSMP-120  
WARNING: Do not connect the power supply module to the external power  
source before installing it into the chassis. Failure to observe this caution could  
result in equipment damage and/or personal injury or death.  
Connect to External Power  
CAUTION: Ensure that the On/Off switch on the power supply module is set  
to “0” when connecting to the external power source. Failure to observe  
this caution could result in damage to, and subsequent failure of, the power  
supply module.  
Replace the CPSMP-120  
CAUTION: Ensure that the power supply module has been disconnected  
from the external power source and the module’s On/Off switch has been  
set to “0”. Failure to observe this caution could result in damage to, and  
subsequent failure of, the power supply module.  
To power the CPSMP-120 power supply module:  
1. Set the On/Off switch on the power supply module to “0”.  
2. Connect the female end of the AC power cord to the male end of the  
external power connector.  
NOTE: The CPSMP-120 power supply module may be “hot swapped” (i.e.,  
replaced while the chassis is in operation) provided the module to be  
replaced has been disconnected from its external power source and the  
module’s On/Off switch has been set to “0”.  
3. Connect the male end of the AC power cord into the correct voltage AC  
rack or wall socket.  
4. Set the power supply module power switch to “I”.  
To replace the CPSMP-120 power supply module:  
5. Verify that the CPSMP-120 power supply module is powered by  
observing the illuminated power LED.  
1. Ensure the On/Off switch on the power supply module is set to “0”.  
2. Disconnect the the male end of the AC power cord from the AC rack or  
wall socket.  
Panel Fastener Screw  
3. Disconnect the female end of the AC power cord from the external power  
connector.  
Power LED  
4. Rotate the attached panel fastener screw counter-clockwise.  
On/Off  
Switch  
External Power Connector  
AC Power Cord  
0
I
Panel  
Fastener  
0
I
Screw  
5. Carefully slide the power supply module to be replaced out of the  
chassis.  
5
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600  
[email protected] -- Click the “Transition Now” link for a live Web chat.  
4
 
CPSMP-120  
Replace the CPSMP-120 -- Continued  
Replace the Fuse  
6. Carefully slide the replacement power supply module into the installation  
slot, aligning the module with the installation guides.  
CAUTION: Ensure that the power supply module has been disconnected  
from the external power source and the module’s On/Off switch has been  
set to “0”. Failure to observe this caution could result in damage to, and  
subsequent failure of, the power supply module.  
NOTE: The CPSMP-120 power supply module may be “hot swapped” (i.e.,  
serviced while the chassis is in operation) provided the module to be serviced  
has been disconnected from its external power supply and the module’s  
On/Off switch has been set to “0”.  
0
I
Panel  
Fastener  
Screw  
0
I
To replace the fuse in the CPSMP-120 power supply module:  
1. Ensure the On/Off switch on the power supply module is set to “0”.  
2. Disconnect the the male end of the AC power cord from the AC rack or  
wall socket.  
7. Ensure that the power supply module is firmly seated inside the chassis.  
8. Rotate the attached panel fastener screw clockwise to secure the power  
supply module to the chassis.  
3. Disconnect the female end of the AC power cord from the external power  
connector.  
9. See the “Connect to External Power” section (page 4) for instructions on  
re-connecting the power supply module to the external power source.  
On/Off Power  
LED  
Switch  
Fuse Holder  
Fuse  
4. From the inside edge of the power receptacle, insert a small flat blade  
screwdriver into the groove on the front, inside edge of the fuse holder  
and carefully pry the fuse holder from the power supply module.  
5. Carefully remove the fuse from the fuse holder.  
6. Install a same size and rating replacement fuse in the fuse holder.  
7. Return the fuse holder and fuse to the installation position in the power  
supply module. Snap the fuse holder into place.  
8. See the “Connect to External Power” section (page 4) for instructions on  
re-connecting the power supply module to the external power source.  
7
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600  
[email protected] -- Click the “Transition Now” link for a live Web chat.  
6
 
CPSMP-120  
Technical Specification  
Troubleshooting  
For use with Transition Networks Model CPSMP-120 or equivalent.  
If the power supply module fails, isolate and correct the failure by determining  
the answers to the following questions and then taking the indicated action:  
Standards  
Dimensions  
Weight  
UL Listed; FCC & CISPR Class A; CE Mark  
3.4" x 2.5" x 11.0" (86 mm x 64 mm x 279 mm)  
1.8 lb (0.82 kg) (approximate)  
1.  
Is the power LED on the CPSMP-120 power supply module  
illuminated?  
NO  
Power Input  
100-240 V, 50/60Hz, 0.4 to 1.0 Amp  
(typical with a fully-loaded chassis)  
Is the power supply module inserted properly into the chassis?  
Is the power supply module properly connected to the external  
power source?  
Power Output  
Fuse  
12VDC at 10.83 Amp (maximum)  
4 Amp, 250V  
Does the external power source provide power?  
Contact Technical Support: US/Canada: 1-800-260-1312,  
International: 00-1-952-941-7600.  
MTBF  
220,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)  
538,224 hours (Bellcore7 V5.0)  
YES  
Environment  
Tmra*:  
0 to 50°C (32 to 122°F )  
-20 to 85°C (-4 to 185°F)  
10 to 90%, non condensing  
0 to 10,000 feet  
Proceed to step 2.  
Storage Temp:  
Humidity:  
Altitude:  
2.  
Is the fuse on the CPSMP-120 power supply intact?  
NO  
CAUTION: See the “Replace the Fuse” section (page 7) for the  
proper method for replacing the fuse to the CPSMP-120 power  
supply module.  
Warranty  
Lifetime  
*Manufacturer’s rated ambient temperature: Tmra range for this power supply  
module depends on the physical characteristics and the installation configuration  
of the Transition Networks PointSystem™ chassis in which this power supply will  
be installed.  
Contact Technical Support: US/Canada: 1-800-260-1312,  
International: 00-1-952-941-7600.  
YES  
For the most up-to-date information on the CPSMP-120 power supply module,  
view the user’s guide on-line at: www.transition.com.  
Contact Technical Support: US/Canada: 1-800-260-1312,  
International: 00-1-952-941-7600.  
9
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600  
[email protected] -- Click the “Transition Now” link for a live Web chat.  
8
 
CPSMP-120  
Contact Us  
Compliance Information  
UL Listed  
Technical Support  
Technical support is available 24 hours a day.  
US and Canada:  
International:  
C-UL Listed (Canada)  
CISPR22/EN55022 Class A  
CE Mark1  
1-800-260-1312  
00-1-952-941-7600  
FCC Regulations  
This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is  
likely to cause harmful interference, in which case the user will be required to correct the  
interference at the user's own expense.  
Transition Now  
Chat live via the Web with Transition Networks Technical Support.  
Log onto www.transition.com and click the Transition Now link.  
Web-Based Seminars  
Transition Networks provides seminars via live web-based training.  
Log onto www.transition.com and click the Learning Center link.  
Canadian Regulations  
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus  
set out on the radio interference regulations of the Canadian Department of Communications.  
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites  
applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le  
brouillage radioélectrique édicté par le ministère des Communications du Canada.  
E-Mail  
Ask a question anytime by sending an e-mail to our technical support staff.  
Address  
European Regulations  
Warning This is a Class A product. In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measures.  
Transition Networks  
6475 City West Parkway  
Minneapolis, MN 55344, USA  
telephone:  
toll free:  
fax:  
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können  
bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für  
entsprechende Gegenmaßnahmen werantwortlich ist.  
952-941-7600  
800-526-9267  
952-941-2322  
Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit  
risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de  
prende les measures spécifiques appropriées.  
DECLARATION OF CONFORMITY  
Name of Mfg:  
Transition Networks  
6475 City West Parkway, Minneapolis MN 55344 USA  
Model:  
Part Number(s):  
Regulation:  
CPSMP-120 Redundant Power Supply 120/240 VAC  
CPSMP-120  
EMC Directive 89/336/EEC  
Purpose: To declare that the CPSMP-120 to which this declaration refers is in  
conformity with the following standards.  
EN 55022:1998+A1:2000 Class A; EN 55024:1998; FCC Part 15 Subpart B; UL 1950;  
EN 61000-3-2:2000; EN 61000-3-3:1995+A1:2001; 21CFR Subpart J  
I, the undersigned, hereby declare that the equipment specified above conforms to the above  
Directive(s) and Standard(s).  
_June 8, 2001_____  
Stephen Anderson, Vice-President of Engineering  
Date  
11  
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600  
[email protected] -- Click the “Transition Now” link for a live Web chat.  
10  
 
Trademark Notice  
All trademarks and registered trademarks are the property of their respective owners.  
Copyright Restrictions  
© 2001, 2004 Transition Networks.  
All rights reserved. No part of this work may be reproduced or used in any form or by any  
means - graphic, electronic, or mechanical - without written permission from Transition  
Networks.  
Printed in the U.S.A.  
33209.C  
 

Tascam CD Player CD A500 User Manual
Telex Power Supply MS 2002 User Manual
Texas Instruments Stereo Receiver DEM DAI3793A User Manual
Toastmaster Food Warmer E17UAC User Manual
Tonino Lamborghini Marine GPS System MDR24 96 User Manual
TP Link Computer Hardware TL WNB51N User Manual
Trane Music Mixer RX 212 User Manual
Transcend Information Network Card TS0MFLRD6E User Manual
Troy Bilt Chipper CS4210 User Manual
Turtle Beach Computer Hardware DDL User Manual