Tripp Lite Switch B119 003 User Manual

Owner’s Manual  
HDMI 3-to-1 Switch with Remote  
Tripp Lite World Headquarters  
1111 W. 35th Street, Chicago, IL 60609 USA  
Model: B119-003  
Package Contents  
• B119-003 HDMI 3-to-1 Switch  
Remote Control  
• Infrared Receiver  
AC Adapter (100-240V), 5V 1A Output  
• Owner's Manual  
Overview and Product Features  
The B119-003 HDMI 3-to-1 Switch with Remote enables you to select one of three HDMI sources to  
be displayed on a single HDMI monitor. Key product features are:  
• 5V 1A power consumption  
• UXGA display support  
Signal rates up to 1.65 Gbps  
Pixel rates up to 165 MHz  
Figure 1.  
Installation and Operation  
Figure 1: Location of Input/Output Connections  
1. Connect user-supplied HDMI cables between the HDMI sources and the B119-003 switch inputs  
marked INPUT A, INPUT B and INPUT C. (Figure 2)  
Figure 2: Connection of HDMI Sources  
Figure 2.  
2. Connect the HDMI cable between the HDMI display and B119-003 switch marked OUTPUT.  
Note: Make sure the HDMI Source is plugged into the INPUT port and the HDMI display is  
plugged into either OUTPUT port. (Figure 3)  
Figure 3: Connection of HDMI Display  
3. Connect the cord from the DC adapter to the DC 5V jack and plug it into a wall outlet. The front  
POWER LED will illuminate. (Figure 4)  
Figure 4: Connection of DC Adapter  
4. Turn on the power to your HDMI display before powering your HDMI sources.  
Figure 3.  
Figure 4.  
Figure 5.  
Figure 5: Selecting an HDMI Source  
5. Connect the Remote Host IR Receiver to the REMOTE INPUT on the back of the switch. You can  
use either the included hand-held remote control or the front SELECT button to toggle between  
HDMI sources. (Figure 5)  
Troubleshooting  
If you experience problems with your B119-003 switch, try the following remedies:  
• Connect an HDMI cable directly between the source and the display to verify that the cable is  
operating. Repeat to test all cables.  
• Once you confirm that all HDMI cables are functional, use two cables to test the ports on the  
B119-003 switch. Plug one cable between the display and the OUTPUT port on the switch. Plug  
the second cable between INPUT A and the source. Repeat with INPUT B and INPUT C, using the  
same source. If all ports function, the B119-003 is operating properly. Note: To ensure that both  
sources and display function properly, the combined cable length should not exceed 5 meters.  
• If the unit is plugged in and the Power LED is not lit, verify that the power supply is functioning.  
Use a voltmeter to measure the output of the DC adapter to verify that 5V is present. If output is  
5V, the DC adapter is functional and the B119-003 switch has failed. Note: The positive (+) is in  
the middle of the plug and the ground (-) is on the exterior of the plug.  
Warranty & Warranty Registration on Page 4  
Note: Follow these instructions and operating procedures to ensure correct performance and to prevent damage to this unit or to its connected devices.  
Copyright © 2007 Tripp Lite. All rights reserved. All trademarks are the sole property of their respective owners.  
 

Tatung Computer Monitor TLM 1903 User Manual
Timex Thermometer TX6130 User Manual
Tripp Lite Surge Protector PS3612 20HW User Manual
Verbatim Computer Drive External Hard Drive NAS User Manual
Vermont Casting Griddle VC0620P VC0680P VC0680N User Manual
ViewSonic Computer Monitor VA2342 LED User Manual
Vivotek Security Camera FD8133V User Manual
VTech Cordless Telephone VT2625 User Manual
Vulcan Hart Convection Oven C24GA10 User Manual
VXI Switch EX7000 User Manual