Universal Remote Control Universal Remote UR3 SR User Manual

*Tip : The equipment will turn off when the  
correct three digit code number has  
been entered. You can verify that you  
have selected the correct code by  
pressing the [MUTE] button, the  
equipment should turn On and Off.  
STEP1 Press the [DEVICE] button (CBL, TV or  
VCR) you wish to verify and the  
[SELECT] button simultaneously for 3  
second.  
Introduction  
The remote control is designed to operate  
three devices, CBL(S/A Explorer and other  
Cable boxes), TV, and VCR/DVD equipments.  
Button Functions  
1
3
Operating Instructions  
For 3 Function  
Cable Remote Control  
*Tip : The LED will light on for 20 seconds.  
The next step must be entered while  
LED is on.  
TV, VCR, CBL  
MENU  
*Note : If there is more than one three digit  
number listed for your brand, try one  
code number at a time until your  
equipment turns off.  
Allow you to turn on and off your  
TV, VCR and CABLE Box.  
Displays cable settings or Menu.  
Replacing Batteries  
Before you program or operate the remote  
control, you must install two new AAA alkaline  
batteries.  
2
STEP2 Press the [INFO] button.  
UR3-SR  
INFO  
The device LED will blink a number of times  
indicating the number of each digit for the  
code. Each digit is separated by a 1 second  
interval of the LED being off.  
Example : One blink, three blinks and eight  
blinks with an interval of 1  
second LED being off, indicates  
the code number 138.  
GUIDE  
Displays channel and program  
information.  
Displays the program guide.  
STEP4 Store the three digit code number by  
pressing the same [DEVICE] button  
once again. The device LED will blink  
twice to confirm that the code has  
been stored.  
HELP  
EXIT  
Displays HELP screen.  
STEP1 Remove the battery compartment cover  
Exits settings, menus, and guides.  
on the back of your remote control.  
SELECT  
Selects and deselects screen item.  
CURSOR KEYS  
*Note : Try all the functions on the remote  
control. If any of the functions do  
not work as they should, repeat from  
Step 2 using the next three digit code  
number from the same brand list.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
Moves through menus or guides.  
A, B, C  
Selects options in menus and IPG.  
Note : Ten blinks is equal to the number 0.  
VCR/DVD KEYS  
D. Programming a second TV  
MUTE  
Perform standard VCR and DVD  
functions when in VCR mode,  
and Video On Demand functions  
when in VOD mode.  
STEP3 Replace the battery compartment  
Turns volume off.  
to VCR Mode.  
cover.  
B. Auto Search Method.  
STEP1 Press the [DEVICE] button [VCR] to  
be programmed and the [SELECT]  
button simultaneously for 3  
seconds.  
VOL+/-  
If none of the three digit code numbers  
assigned to your brand turns off your  
equipment or the code table does not list your  
brand, you can use the Auto Search Method  
to find the correct three digit code number for  
your equipment by the following steps:  
Adjusts the volume up and down.  
Install two  
AAA alkaline batteries  
as shown here  
CH+/-  
Selects channels up or down.  
LAST  
Returns to last channel viewed.  
*Tip : The LED will light on for 20 seconds.  
The next step must be entered while  
LED is on.  
STEP1 Turn on the equipment you wish to  
VCR/VOD  
NUMBER KEYS  
STEP2 Press the [TV] button to pick up the  
Switches the VCR controls into  
Video On Demand controls.  
program. (CBL, TV, VCR or DVD)  
Allow direct access to specific channels  
and menu options.  
TV code table.  
STEP2 Press the [DEVICE] button (CBL, TV or  
VCR) to be programmed and the  
[SELECT] button simultaneously for 3  
second. The device LED will turn on  
indicating that it is ready to be  
programmed.  
STEP3 Point the remote control toward the  
equipment and enter the three digit  
code number assigned to your TV  
brand from the code tables.  
VOD  
Access Video On Demand.  
STEP4 Store the three digit code number by  
pressing the [DEVICE] button (VCR)  
once again. The device LED will blink  
twice to confirm that the code has  
been stored.  
*Tip : The LED will light on for 20 seconds. The  
next step must be entered while LED is  
on.  
STEP3 Press the [CH+] or [CH-] button one  
step at a time. The remote will emit a  
series of Power ON/OFF code signals.  
Release the [CH+] or [CH-] button as  
soon as the equipment turns off.  
E. Programming For Advanced Function.  
Operations  
4
Programming the Remote Control.  
5
In the CABLE device mode, the A,B,C and  
VOD buttons can be programmed to act as  
a macro button to send out up to 10  
commands with one button press.  
Default State:  
A. Three Digit Code Method.  
The remote control can be programmed by pressing in a three digit code number that  
corresponds to particular manufacturers and brands of Audio/Video equipment.  
The three digit code numbers are listed in the code table of the instruction manual.  
Device Default: Cable mode with S/A Explorer.  
Volume Default: Vol +/- & Mute from TV mode.  
*Tip :You can verify that you selected the  
correct code by pressing the [MUTE]  
button. The equipment should turn On  
and Off.  
STEP1 Press the [CBL] button to select the  
CABLE mode.  
VOD button:  
STEP1 Turn on the equipment you wish to program. (CBL, TV, VCR or DVD)  
STEP4 Press the same [DEVICE] button to  
store the code. The Device LED will  
blink twice to confirm that the code  
has been stored.  
STEP2 Press the [VOD] button and the  
[SELECT] button simultaneously for  
3 second. The CBL device LED will  
turn on for 20 seconds.  
This button sends out CH 999 with default and a  
customer can program any commands, up to 10  
commands. Please refer to section E for details.  
STEP2 Press the [DEVICE] button (CBL, TV or VCR) to be programmed and the [SELECT] button  
simultaneously for 3 second. The device LED will turn on indicating that it is ready to be  
programmed.  
Universal Remote Control, Inc.  
*Tip : The LED will light on for 20 seconds. The next step must be entered while LED is on.  
STEP3 Press up to 10 buttons you wish to  
store. The CBL device LED will blink  
once for each command entered.  
C. To Find the Three Digit Code  
Number That was Stored in  
the Device.  
STEP3 Point the remote control toward the equipment and enter the three digit code number  
OCE-0009A Rev 01(11/21/02)  
assigned to your brand from the code tables.  
 

Taylor Thermometer 9867 User Manual
Technicolor Thomson Network Router TG576 v7 User Manual
Thecus Technology Server N8800 User Manual
Tokina Camera Lens TM50Z1040 User Manual
Toshiba Telephone DP5000 Series User Manual
Ultra electronic Printer 3503 1002 User Manual
Uniflame Outdoor Fireplace WAD1009SP User Manual
VeriFone IP Phone Omni 37xx User Manual
Verilux Indoor Furnishings CWST1 User Manual
Vinotemp Beverage Dispenser VT 34 TS User Manual