Viking Ventilation Hood DCH User Manual

VENTILATION  
Built-In 10”H. Wall Hood w/Ventilator/  
12”H. Chimney Wall Hood w/Ventilator  
Standard Features & Accessories  
All models include  
• Heavy-duty construction  
Professional 10”H. hoods include  
ranges, 30”W. non-griddle/grill  
rangetops, and 30”W. cooktops  
• VWH3610—36”W.  
o Recommended for use with 36”W.  
non-griddle/grill ranges, 36”W. non-  
griddle/grill rangetops, and 36”W.  
cooktops  
o Virtually seamless stainless steel  
design with no visible screws  
• Heat sensor turns the ventilator on full  
power when cooking temperatures  
reach uncomfortable levels  
• Recommended for 24”W., 30”W. &  
36”W. non-griddle/grill ranges,  
rangetops, and cooktops  
• Commercial-type size, design, and styling  
• Allow replacement of most older  
hoods with minimal cabinet alteration  
• Commercial-type baffle filter system  
efficiently removes grease and heated  
vapors from the air; especially  
designed for use with commercial-  
type products  
DESIGNER CHIMNEY WALL HOODS,  
12”H./24”D.  
• 460 CFM interior-power ventilator  
comes standard with product  
o Variable speed controls for custom  
venting—separate on/off switch  
allows you to leave ventilator at  
favorite/most-used setting  
Two 50-watt halogen lights with  
dimmer control  
o Power switch and dimmer control  
are separate, allowing you to leave  
dimmer at favorite position  
Designer 12”H. hoods include  
• Professional-type size, design, and  
styling  
• Delay function—can be set to shut off  
from 10 – 30 minutes later (10 min.  
increments)  
• 12-hour timer built into controls  
Two dishwasher-safe stainless steel  
mesh filters are easily removed for  
quick cleaning (frame and mesh are  
stainless steel)  
• DCH3042—30”W.  
o Recommended for use with 30”W.  
ranges, 30”W. non-griddle/grill  
rangetops, and 30”W. cooktops  
• DCH3642—36”W.  
o Recommended for use with 36”W.  
ranges, 36”W. non-griddle/grill  
rangetops, and 36”W. cooktops  
• Easy cleanup  
Model numbers  
o Design of low-profile filter system  
means less interior hood space to  
be cleaned  
o Canopy interior is completely lined  
in stainless steel for increased  
rigidity, seamless appearance, and  
easy cleaning  
PROFESSIONAL WALL HOODS, 10”H./21”D.  
• VWH2410—24”W.  
o Recommended for use with 24”W.  
non-griddle/grill ranges (for larger  
equipment, use 18”H. hood)  
• VWH3010—30”W.  
o Recommended for use with 30”W.  
Model Options  
VWH Professional  
Wall Hood  
DCH Designer Chimney  
Wall Hood  
FINISH DETAILS FOR PROFESSIONAL MODELS  
Racing Red (RR), Apple Red (AR),  
Burgundy (BU), Plum (PL), Chocolate  
(CH), and Cobalt Blue (CB).  
supports/brackets and hooks  
(included).  
o Brass Trim Option (BR)—nameplate,  
rail, supports/brackets, and hooks  
(included). Brass components have a  
durable protective coating for  
• Stainless Steel (SS), Black (BK), White  
(WH), Metallic Silver (MS), Graphite Gray  
(GG), Stone Gray (SG), Taupe (TP), Biscuit  
(BT), Cotton White (CW), Oyster Gray  
(OG), Golden Mist (GM), Lemonade (LE),  
Sage (SA), Mint Julep (MJ), Sea Glass  
(SE), Iridescent Blue (IB), Viking Blue (VB),  
Pumpkin (PM), Racing Red (RR), Apple  
Red (AR), Burgundy (BU), Plum (PL),  
Chocolate (CH), and Cobalt Blue (CB).  
• Finish designates front and sides.  
• Accessory Rail Option—Front of hood.  
(Must be ordered factory installed)  
o Stainless Steel/Chrome (CR)—  
• Finish designates front and sides.  
• Accessory Rail Option—Front of hood.  
(Must be ordered factory installed)  
o Stainless Steel/Chrome (CR)—  
Stainless steel rail with chrome  
supports/brackets and hooks  
(included).  
o Brass Trim Option (BR)—rail,  
supports/brackets, and hooks  
(included). Brass components have a  
durable protective coating for  
maintenance-free normal use.  
maintenance-free normal use.  
FINISH DETAILS DESIGNER MODELS  
• Stainless Steel (SS), Black (BK), White  
(WH), Metallic Silver (MS), Graphite  
Gray (GG), Stone Gray (SG), Taupe  
(TP), Biscuit (BT), Cotton White (CW),  
Oyster Gray (OG), Golden Mist (GM),  
Lemonade (LE), Sage (SA), Mint Julep  
(MJ), Sea Glass (SE), Iridescent Blue  
(IB), Viking Blue (VB), Pumpkin (PM),  
Stainless steel rail with chrome  
ORDERING INSTRUCTIONS  
First specify model number, followed by color code (VWH2410SS). If ordering optional decorative rail, specify code at end  
(VWH2410SSCR).  
PLANNING AND DESIGN GUIDE  
RELEASED 12/1/07  
©2007 VRC— INFORMATION SUBJECT TO CHANGE  
V I K I N G R A N G E . C O M  
1 - 8 8 8 - V I K I N G 1  
 
VENTILATION  
Built-In 10”H. Wall Hood w/Ventilator/  
12”H. Chimney Wall Hood w/Ventilator  
Dimensions & Specifications  
CLEARANCE DIMENSIONS  
60”min.  
24”min.  
(15  
(61.0 cm)  
2.4 cm)  
to  
63”max.  
to  
27”max.*  
(16  
(68.6 cm)  
0.0 cm)  
36”  
(91.4 cm)  
PROFESSIONAL  
*Note: When installing with a 24” high-shelf, the  
27” (68.6 cm) max. dimensions must be used.  
66”min.  
30”min.  
(167.6 cm)  
(76.2 cm)  
to  
69”max.  
to  
33”max.  
(175.3 cm)  
(83.8 cm)  
36”  
cm)  
(91.4  
DESIGNER  
PLANNING AND DESIGN GUIDE  
RELEASED 12/1/07  
©2007 VRC— INFORMATION SUBJECT TO CHANGE  
V I K I N G R A N G E . C O M  
1 - 8 8 8 - V I K I N G 1  
 
VENTILATION  
Built-In 10”H. Wall Hood w/Ventilator/  
12”H. Chimney Wall Hood w/Ventilator  
Installation Requirements  
VWH Professional  
Wall Hood  
DCH Designer Chimney  
Wall Hood  
UTILITY REQUIREMENTS  
Proper installation/ ducting is  
extremely important to ensure  
maximum performance. Use a qualified  
and trained installer.  
o Straight runs and  
gradual turns are best; for  
example, each 90° elbow  
is equivalent to 5’ – 10’  
(1.52 – 3.05 cm) of  
ELECTRICAL  
• Hardwire direct with two-wire  
with ground  
• 120 VAC/60 Hz  
• Max. amp usage—5.6  
DUCTING  
straight run.  
• 460 CFM interior (blower  
included)  
• 7” round duct  
PLUMBING  
Not applicable  
o Never use flexible duct; it  
creates back pressure/air  
turbulence and greatly  
reduces performance.  
• Check with a qualified and  
trained installer for local  
codes and makeup air  
requirements, if any.  
• Max. duct run length—50’  
(152.4 m)  
GAS  
Not applicable  
o Duct run length is for  
general reference only;  
for longer duct runs,  
increase duct size and  
contact a qualified and  
trained installer.  
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be  
greatly overstated.  
Model  
Interior Ventilator Kits  
460 CFM standard  
460 CFM standard  
460 CFM standard  
460 CFM standard  
460 CFM standard  
Interior Duct Size  
7” (17.8 cm)  
Interior Max. Amps  
VWH2410  
VWH3010  
VWH3610  
DCH3042  
DCH3642  
5.6  
5.6  
5.6  
5.6  
5.6  
7” (17.8 cm)  
7” (17.8 cm)  
7” (17.8 cm)  
7” (17.8 cm)  
PLANNING AND DESIGN GUIDE  
RELEASED 12/1/07  
©2007 VRC— INFORMATION SUBJECT TO CHANGE  
V I K I N G R A N G E . C O M  
1 - 8 8 8 - V I K I N G 1  
 
VENTILATION  
Built-In 10”H. Wall Hood w/Ventilator/  
12”H. Chimney Wall Hood w/Ventilator  
Installation Notes & Accessories  
Recirculating Hood Conversion Kits  
• Stainless Steel (SS)  
• Eliminates ducting  
• Kit includes  
o Two charcoal filters  
o Installation hardware  
o Top vent/grille  
Professional—4”H. x 12”D.  
Designer—2”H. x 12”D.  
Model  
VRK24  
VRK30  
VRK36  
DRK30  
DRK36  
Description  
Approx. ship wt. lbs. (kg)  
Professional 24”W. conversion kit  
Professional 30”W. conversion kit  
Professional 36”W. conversion kit  
Designer 30”W. conversion kit  
Designer 36”W. conversion kit  
10 (4.5)  
13 (5.9)  
16 (7.3)  
15.4 (7)  
15.4 (7)  
Charcoal Filters  
• For use with VRK & DRK conversion kits  
• Recommended replacement every 6 – 12 months  
Model  
CFV11  
CFV13  
CF-D12  
CF-D14  
Description  
Approx. ship wt. lbs. (kg)  
Professional hood filter for 24”W.  
Professional hood filter for 30”W. & 36”W.  
Designer hood filter for 30”W.  
Designer hood filter for 36”W.  
1 (0.5)  
2 (0.9)  
2 (0.9)  
2 (0.9)  
Duct Covers  
• Specify finish code following accessory model number (for example, DCW24-SS)  
o Professional models  
For VWH hoods  
12”D.  
Extends height of hood by 12”—conceals duct  
Available in Stainless Steel (SS), Black (BK), White (WH), Almond (AL), Biscuit (BT), Stone Gray (SG), Graphite Gray  
(GG), Burgundy (BU), Lemonade (LE), Mint Julep (MJ), Forest Green (FG), Viking Blue (VB), Cobalt Blue (CB), and  
Eggplant (EP).  
o Designer models  
For DCH hoods  
For 8’ – 9’ ceilings  
Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).  
Not needed if using a DCLF1610  
Model  
DCW24  
DCW30  
DCW36  
DCC16  
Description  
Approx. ship wt. lbs. (kg)  
9 (4.0)  
Professional 24”W. duct cover  
Professional 30”W. duct cover  
Professional 36”W. duct cover  
Designer adjustable duct cover – for DCH 30” & 36” models  
10 (4.5)  
11 (5.0)  
20 (9.0)  
PLANNING AND DESIGN GUIDE  
RELEASED 12/1/07  
©2007 VRC— INFORMATION SUBJECT TO CHANGE  
V I K I N G R A N G E . C O M  
1 - 8 8 8 - V I K I N G 1  
 
VENTILATION  
Built-In 10”H. Wall Hood w/Ventilator/  
12”H. Chimney Wall Hood w/Ventilator  
Installation Notes & Accessories  
Duct Cover Extension  
• For DCH hoods  
• 16”W. x 12”D. x 28 – 40”H.  
• Extends height of hood by up to 12” (for 10’ ceilings)  
• Replaces adjustable duct cover supplied standard with hood  
• Specify finish code following accessory model number (for example, DCCE1610-SS)  
• Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).  
Model  
Description  
Approx. ship wt. lbs. (kg)  
DCCE1610  
Designer duct cover extension  
7 (15.4)  
Backsplashes  
• Stainless Steel (SS)  
• 30”H.  
• For both VWH & DCH hoods  
• Backsplashes protect the wall space below hood  
• Create a continuous finish between cooking surface and hood  
• Low maintenance, easy to clean  
• Hemmed edges with screw holes  
• Kit includes backsplash and fastening screws  
Model  
BKS24  
BKS30  
BKS36  
Description  
Approx. ship wt. lbs. (kg)  
24”W. backsplash  
30”W. backsplash  
36”W. backsplash  
5 (2.3)  
7 (3.2)  
9 (4.1)  
Warming Shelf Panels  
• Stainless Steel (SS)  
• 12”D. X 12”H.  
• For both VWH & DCH hoods  
• Shelf panels hold cookware and condiments  
• Kit includes shelf (or shelves) and fastening screws  
• Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash  
• 5-7/8”W. X 10-1/8”D.  
Model  
WGP24  
WGP30  
WGP36  
Description  
Approx. ship wt. lbs. (kg)  
24”W. warming shelf panel (one shelf)  
30”W. warming shelf panel (one shelf)  
36”W. warming shelf panel (two shelves)  
6 (2.7)  
9 (4.1)  
12 (5.4)  
Compliance Information  
WARRANTY SUMMARY*  
• One-year full warranty—complete product  
• Five-year limited warranty—all ventilator motors  
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items  
* For complete warranty see Use & Care Guide. Warranty valid on Viking products shipped within the United States and Canada.  
PLANNING AND DESIGN GUIDE  
RELEASED 12/1/07  
©2007 VRC— INFORMATION SUBJECT TO CHANGE  
V I K I N G R A N G E . C O M  
1 - 8 8 8 - V I K I N G 1  
 

Telex TV Antenna ALP 450 User Manual
Toastmaster Convection Oven MH36 User Manual
Toshiba All in One Printer GA 1191 User Manual
Tricity Bendix Oven BD 912 User Manual
Tripp Lite Network Cables N201 010 BK User Manual
Uniden Cordless Telephone DX8200 User Manual
Univex Water Heater NRQSS00110 User Manual
Vienna Acoustics Speaker Waltz Grand Series User Manual
VocoPro Karaoke Machine CLUB 6800 User Manual
Wayne Dalton Garage Door Opener DS 350 User Manual