Wayne Dalton Automobile Electronics 3966 User Manual

Mounting  
MODEL 3966  
Wireless Keyless Entry System  
How Your Keyless Entry  
Operates Your Opener  
NOTE: With new installations, it is  
recommended that the keyless entry be  
programmed before mounting to wall.  
Pre-drill a 5/64 pilot  
hole 3/4" deep  
Locate Keyless Entry Unit: within sight of door,  
at a minimum height of 5 feet so it cannot be  
reached by small children, and away from all  
moving parts of the door.  
The following explains how your Keyless Entry  
can be used to OPEN, CLOSE, START, and  
STOP your door.  
Choose a convenient location that does not  
interfere with the normal opening and closing  
operation of the door, such as the door jamb.  
Enter your 5-digit PIN (personal identification  
number); door will begin to move  
1.  
CAUTION: The keypad  
should be mounted a  
minimum of 5 feet from  
the floor to keep it out  
of the reach of small  
children.  
Two screws are included  
for proper mounting into  
wood or other similar  
material. If you're  
mounting into some other  
material, consult a  
building contractor to  
insure proper hardware is  
used for a secure  
NOTE: If you inadvertently enter an incorrect  
code, the door will not move To Reset, press  
and hold the "7/8" and "9/0" buttons for 2  
seconds and reenter your PIN number.  
NOTE: This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference when the equipment is operated in  
a residential environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instruction manual, may cause harmful interference to  
radio communications. However, there is no guarantee  
that interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception, which can  
be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by  
one or more of the following measures:  
2. Unit remains active for next 25 sec.  
Pressing any key, will stop the door if  
opening, and stop or reverse the door if  
closing.  
Battery Replacement  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and  
receiver.  
- Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
- Consult the dealer or an experienced radio/TV  
technician for help.  
mounting.  
Once you  
Under normal operating conditions, the  
battery should be changed once every 12  
months. Dispose of used batteries  
properly. To replace battery perform the  
following steps:  
have  
determined  
the  
mounting  
Your new Model 3966 Wireless Keyless Entry  
contains a state-of-the-art wireless digital  
transmitter capable of operating an unlimited  
number of compatible garage door openers.  
location,  
use the  
drilling  
template  
to  
determine  
hole  
positions  
and drill a  
A. Snap open case with a coin and remove  
old batteries.  
For added security, your Wireless Keyless Entry  
utilizes a "rolling code" technology that, each  
time the transmitter communicates with the  
receiver, sets a new code, selecting from  
millions of combinations, reducing the possibility  
of electronic equipment causing unwanted  
access.  
B. Replace batteries (two CR2032 or  
equivalent) and snap case together.  
Front Case  
5/64" pilot  
hole  
Pre-drill a 5/64 pilot  
hole 3/4" deep  
For proper operation it is important that  
you follow the programming directions  
and sequence as written.  
3/4" deep for the two mounting screws.  
Snap open the Keyless Entry case with a coin.  
Separate the front case from the back case.  
Mount the back case and secure with screws  
provided. Do not over tighten the screws as  
this may bend or damage the back case. Install  
and snap the front case onto the back case.  
Remove paper backing from "Changing  
Wayne-Dalton Corp.  
One Door Drive n Mt. Hope, OH 44660  
888-827-3667  
Drilling Template  
For Keyless Entry  
(2) Coin Cells  
Rear Case  
Personal Identification Number" label and apply  
label to a clean surface inside garage.  
Batteries (CR2032)  
Coin Slot  
 

Toastmaster Convection Oven RHTOV211CAN User Manual
Toshiba Flat Panel Television 23L1350U User Manual
Toshiba TV Converter Box L5232 User Manual
Triarch Indoor Furnishings 29771 User Manual
Tricity Bendix Oven BS 612 2 User Manual
Troy Bilt Blower TB4BP User Manual
True Fitness Fitness Equipment TrueStretch User Manual
ViewSonic Flat Panel Television VPW425 User Manual
Waterford Appliances Indoor Fireplace E61 LP User Manual
Weber Gas Grill 55568 User Manual